TX Product(s) used: e.g J-R Programmer, Coolrunner Rev C
Console Type: Trinity
NAND size: 4GB
Dashboard version: 16547
CB version: 9231
Screenshot of NAND details from J-Runner:
Unbenannt-1.jpg
J-Runner log:
updflash.bin log (if applicable):
Image of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)
Description of problem:
Hi,
i just installed Coolrunner Rev C. First i tried tried with blue Cable on Cpu_Rst without success. So I switched to the shielded cable. I Connected black wire to Gnd. If i power on the Console it was ersetting permanently. So i cuttet Gnd wire and powered on again. The console did boot into Xell and i was able to recieve the CPU key. I Buleded a new Image and flashed it to the Nand.
Everything worked fine, but cpu reset signal was sended about 2-5 times it varies each time. So i Tried to solder Gnd wire on again and same Problem. I cuttet it again but the console will still reset permanently as you can hear. If i set the switch to phat it wors correct and sends a reset signal every 5 seconds but console won't glitch. I've solderd the Gnd wire to the Av Port.
Coolrunner is in default no jumpers changed
Sorry i have no Pictures at the moment because my camera is not at home, i'll add later.
Thanks for your help
Thomas
Was the console working before you started: Y
Console Type: Trinity
NAND size: 4GB
Dashboard version: 16547
CB version: 9231
Screenshot of NAND details from J-Runner:
Unbenannt-1.jpg
J-Runner log:
Code:
Getting info from ip 192.168.2.101...
LockDownValue is 11
Getting info from ip 192.168.2.101...
LockDownValue is 22
Tip: Load the nand on source to have quicker results.
Scanning...
No Xbox Detected
Finished
Initializing nanddump1.bin..
Trinity
Nand Initialization Finished
Initializing nanddump1.bin..
Trinity
Nand Initialization Finished
Getting info from ip 192.168.2.101...
LockDownValue is 11
Initializing nanddump1.bin..
CpuKey is Correct
Added Key to Database
Trinity
Nand Initialization Finished
Moving All files from output folder to C:\Users\Tombo\Downloads\467479502805
Getting info from ip 192.168.2.101...
LockDownValue is 22
Load Files Initiliazation Finished
16203
Started Creation of the 16203 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.09.639
---------------------------------------------------------------
base path changed to C:\Users\Tombo\Desktop\Xbox 360\Rgh\xeBuild
---- { Image Build Mode } ----
building glitch2 image
---------------------------------------------------------------
C:\Users\Tombo\Downloads\467479502805\updflash.bin image built, info:
---------------------------------------------------------------
Kernel : 2.0.16203.0
Console : Trinity
NAND size : 16MiB
Build : Glitch (v2)
Xell : power on console with console eject button
Serial : 467479502805
ConsoleId : 019776902157
MoboSerial: 7256561205450285
Mfg Date : 07/09/2010
CPU Key : 119B710A4D6993B9B45565AAEC67E127
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : 642B6158B94700BC84DF232C53FE68D8
CF LDV : 11
KV type : type2 (hashed - unchecked, master key not available)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to C:\Users\Tombo\Downloads\467479502805
Image is Ready
Initializing updflash.bin..
Trinity
Nand Initialization Finished
Version: 10
Flash Config: 0x00023010
Writing Nand
updflash.bin
Error: 202 writing block 138
Done!
in 3:40 min:secImage of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)
Description of problem:
Hi,
i just installed Coolrunner Rev C. First i tried tried with blue Cable on Cpu_Rst without success. So I switched to the shielded cable. I Connected black wire to Gnd. If i power on the Console it was ersetting permanently. So i cuttet Gnd wire and powered on again. The console did boot into Xell and i was able to recieve the CPU key. I Buleded a new Image and flashed it to the Nand.
Everything worked fine, but cpu reset signal was sended about 2-5 times it varies each time. So i Tried to solder Gnd wire on again and same Problem. I cuttet it again but the console will still reset permanently as you can hear. If i set the switch to phat it wors correct and sends a reset signal every 5 seconds but console won't glitch. I've solderd the Gnd wire to the Av Port.
Coolrunner is in default no jumpers changed
Sorry i have no Pictures at the moment because my camera is not at home, i'll add later.
Thanks for your help
Thomas
Was the console working before you started: Y