about JR Programmer V2.
(1)Is xbox360 power supply necessary while JR Programmer V2 NAND reading.
(2)What is the function of JP3 switch on JR Programmer V2 board,
and which position should be set while NAND reading.
(3)What is the function of JP-BL switch (near the JP-RST switch)
on JR Programmer V2 board, and which position should be set while NAND reading.
4)about the QSB.
In general, for all soldering points on which is provided so as to be electrically connected to the motherboard is either would no problem even if we soldered all available soldering points ? or will not work properly without all of the available soldering points in reverse?
As a specific example, the case of the TX JRP / NANDX / CR Corona QSB Install Kit V3, there is a solder point of the 16 places in the QSB. (We excluded soldered points 5V, E, K, F. Because these are not soldered directly to the motherboard ). When using this QSB only for JRP V2 , my understanding is that, it works properly if we only solder the required seven locations. is this correct?
in this case , once we soldered this required seven portions , I understand nine remaining soldering points are arbitrary.
Namely we may solder nine remaining soldering points or we may not solder. in this case remaining 9 points are not a matter . is this correct (good soldering techniques is assumed.) ?
Because there is no Tutorial of soldering the QSB, novice wondering points as described above.
As for JXecuter POST SLIM QSB V3, there is a solder point of 8 points which are electrically connected to the motherboard, but it is not mentioned at all in the following commentary in the article.
http://team-xecuter.com/forums/showt...highlight=SLIM, QSB, install, solder points
In this thread , only the soldering position of QSB on post_out, of cpu_rst are mentioned.
For use with Slim Prorto V2, there are eight soldering points on the QSB, but these will do no problem even if soldered to all Moththerboard?
Will it not work properly without soldering eight all in reverse?
In this case both incorrect, where is tutorial for soldering points by application ?
Sorry for poor English
thank you
(1)Is xbox360 power supply necessary while JR Programmer V2 NAND reading.
(2)What is the function of JP3 switch on JR Programmer V2 board,
and which position should be set while NAND reading.
(3)What is the function of JP-BL switch (near the JP-RST switch)
on JR Programmer V2 board, and which position should be set while NAND reading.
4)about the QSB.
In general, for all soldering points on which is provided so as to be electrically connected to the motherboard is either would no problem even if we soldered all available soldering points ? or will not work properly without all of the available soldering points in reverse?
As a specific example, the case of the TX JRP / NANDX / CR Corona QSB Install Kit V3, there is a solder point of the 16 places in the QSB. (We excluded soldered points 5V, E, K, F. Because these are not soldered directly to the motherboard ). When using this QSB only for JRP V2 , my understanding is that, it works properly if we only solder the required seven locations. is this correct?
in this case , once we soldered this required seven portions , I understand nine remaining soldering points are arbitrary.
Namely we may solder nine remaining soldering points or we may not solder. in this case remaining 9 points are not a matter . is this correct (good soldering techniques is assumed.) ?
Because there is no Tutorial of soldering the QSB, novice wondering points as described above.
As for JXecuter POST SLIM QSB V3, there is a solder point of 8 points which are electrically connected to the motherboard, but it is not mentioned at all in the following commentary in the article.
http://team-xecuter.com/forums/showt...highlight=SLIM, QSB, install, solder points
In this thread , only the soldering position of QSB on post_out, of cpu_rst are mentioned.
For use with Slim Prorto V2, there are eight soldering points on the QSB, but these will do no problem even if soldered to all Moththerboard?
Will it not work properly without soldering eight all in reverse?
In this case both incorrect, where is tutorial for soldering points by application ?
Sorry for poor English
thank you