**This isn't my first time glitching an xbox , just my first time posting in this forum for help.
The Problem: When the console is powered on, the ROL and fan turn on for about 1 second, then the consoles turns itself off. The power supply is working fine. The light is orange in stand by. When I try to power on the console, it turns green for 1 second, then it turns back to orange.
What lead to the problem: First I opened the Xbox and determined that it was a Corona V5. I soldered the necessary wires to the MOBO and connected my Nand-X to my computer. I brided R2C6 & R2C7, Didn't need to bridge R2C10. I dumped the nand twice. Nands were the same. Then I flashed my DGX 1.1 with the RGX Corona C file. I hooked my Nand-X back up to the MOBO & wrote the CORONA_16MB.ecc using the 'Advanced' tab in J-Runner. I soldered the DGX 1.1 to the MOBO and connected my TX Postfix adapter. Next I soldered 3 COMS wires that connect my X360 USB Pro to the MOBO. This is where things started to go wrong. After everything was wired up correctly I turned on the Xbox so that I could boot Xell & recover the CPU key. After about 6 cycles the green LED on the DGX board stopped blinking so I clicked the 'Monitor COM" button then clicked on "open port" in J-runner but nothing happened. I knew something was wrong because usually the key pops right up. I checked the Xbox and noticed that the Ground wire from my X360 USB Pro was no longer soldered to its correct place. So I turned the xbox off, took my soldering iron and soldered the wire back to the MOBO. Before I did my soldering I remembered that I updated J-Runner the night before and I had to ad the latest dashboards to J-Runner. I soldered the COMS ground cable back to the MOBO and powered on the Xbox again. Thats when it stopped booting up. It would turn on for one second then turn back off. I checked my soldering and noticed that I had accidently soldered the COMS ground wire too close to the DGX 5V power wire and they were touching. I tried powering on the Xbox multiple times while these two wires were soldered together. I desoldered the DGX board and flashed the original Nand back to the MOBO but it still will not power on.Bad connection.jpgHeres the log:
IMAG0171.jpgHeres the board after I desoldered everything and flashed nand back to stock
The Problem: When the console is powered on, the ROL and fan turn on for about 1 second, then the consoles turns itself off. The power supply is working fine. The light is orange in stand by. When I try to power on the console, it turns green for 1 second, then it turns back to orange.
What lead to the problem: First I opened the Xbox and determined that it was a Corona V5. I soldered the necessary wires to the MOBO and connected my Nand-X to my computer. I brided R2C6 & R2C7, Didn't need to bridge R2C10. I dumped the nand twice. Nands were the same. Then I flashed my DGX 1.1 with the RGX Corona C file. I hooked my Nand-X back up to the MOBO & wrote the CORONA_16MB.ecc using the 'Advanced' tab in J-Runner. I soldered the DGX 1.1 to the MOBO and connected my TX Postfix adapter. Next I soldered 3 COMS wires that connect my X360 USB Pro to the MOBO. This is where things started to go wrong. After everything was wired up correctly I turned on the Xbox so that I could boot Xell & recover the CPU key. After about 6 cycles the green LED on the DGX board stopped blinking so I clicked the 'Monitor COM" button then clicked on "open port" in J-runner but nothing happened. I knew something was wrong because usually the key pops right up. I checked the Xbox and noticed that the Ground wire from my X360 USB Pro was no longer soldered to its correct place. So I turned the xbox off, took my soldering iron and soldered the wire back to the MOBO. Before I did my soldering I remembered that I updated J-Runner the night before and I had to ad the latest dashboards to J-Runner. I soldered the COMS ground cable back to the MOBO and powered on the Xbox again. Thats when it stopped booting up. It would turn on for one second then turn back off. I checked my soldering and noticed that I had accidently soldered the COMS ground wire too close to the DGX 5V power wire and they were touching. I tried powering on the Xbox multiple times while these two wires were soldered together. I desoldered the DGX board and flashed the original Nand back to the MOBO but it still will not power on.Bad connection.jpgHeres the log:
Code:
===================================================
Thursday, July 25, 2013 8:46:36 PM
J-Runner v0.2 Beta (289) Started
Checking Files
Finished Checking Files
Checking Console..
Version: 03
Flash Config: 0x00043000
CB Version: 13181
Corona
Version: 03
Flash Config: 0x00043000
CB Version: 13181
Corona
Reading Nand to C:\Users\Mike\Documents\J-Runner v02 Beta (288) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 2:19 min:sec
Initializing nanddump1.bin..
Reading Nand to C:\Users\Mike\Documents\J-Runner v02 Beta (288) Core Pack\output\nanddump2.bin
Reading Nand
Nand Initialization Finished
Done!
in 2:19 min:sec
Comparing...
Nands are the same
Comparing...
Nands are the same
Programming Coolrunner
C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_C_CR_EN_P50.xsvf
Version: 03
Flashing C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_C_CR_EN_P50.xsvf to CoolRunner
Input Filesize: AA78
Output Filesize: 3BBF
Done!
Version: 03
Flash Config: 0x00043000
Writing Nand
CORONA_16MB.ecc
Done!
in 0:10 min:sec
Creating Directory C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\xeBuild\15574\bin
Downloaded *xeBuild/15574/bin/nofcrt.bin
Downloaded *xeBuild/15574/bin/nohdd.bin
Downloaded *xeBuild/15574/bin/nohdmiwait.bin
Downloaded *xeBuild/15574/bin/nomu.bin
Downloaded *xeBuild/15574/bin/notrinmu.bin
Downloaded *xeBuild/15574/bin/patches_falcon.bin
Downloaded *xeBuild/15574/bin/patches_fat.bin
Downloaded *xeBuild/15574/bin/patches_g2falcon.bin
Downloaded *xeBuild/15574/bin/patches_g2jasper.bin
Downloaded *xeBuild/15574/bin/patches_g2trinity.bin
Downloaded *xeBuild/15574/bin/patches_g2zephyr.bin
Downloaded *xeBuild/15574/bin/patches_jasper.bin
Downloaded *xeBuild/15574/bin/patches_trinity.bin
Downloaded *xeBuild/15574/bin/patches_g2corona.bin
Downloaded *xeBuild/15574/bin/patches_xenon.bin
Downloaded *xeBuild/15574/bin/patches_zephyr.bin
Downloaded *xeBuild/15574/su20076000_00000000
Downloaded *xeBuild/15574/xenonclatin.xtt
Downloaded *xeBuild/15574/xenonjklatin.xtt
Downloaded *xeBuild/15574/ximedic.xex
Downloaded *xeBuild/15574/_glitch.ini
Downloaded *xeBuild/15574/_glitch2.ini
Downloaded *xeBuild/15574/_jtag.ini
Downloaded *xeBuild/15574/_retail.ini
Downloaded *common/cba_1942.bin
Downloaded *common/cba_4574.bin
Downloaded *common/cba_5772.bin
Downloaded *common/cba_5774.bin
Downloaded *common/cba_6754.bin
Downloaded *common/cba_9188.bin
Downloaded *common/cba_6752.bin
Downloaded *common/cba_9231.bin
Downloaded *common/cba_13121.bin
Downloaded *common/cba_13181.bin
Downloaded *common/cbb_1942.bin
Downloaded *common/cbb_4574.bin
Downloaded *common/cbb_5772.bin
Downloaded *common/cbb_5774.bin
Downloaded *common/cbb_6752.bin
Downloaded *common/cbb_6754.bin
Downloaded *common/cbb_9188.bin
Downloaded *common/cbb_9231.bin
Downloaded *common/cbb_13121.bin
Downloaded *common/cbb_13181.bin
Downloaded *common/cb_1921.bin
Downloaded *common/cb_1940.bin
Downloaded *common/cb_4558.bin
Downloaded *common/cb_4578.bin
Downloaded *common/cb_4579.bin
Downloaded *common/cb_5770.bin
Downloaded *common/cb_5771.bin
Downloaded *common/cb_6723.bin
Downloaded *common/cb_6750.bin
Downloaded *common/cd_1921.bin
Downloaded *common/cd_1942.bin
Downloaded *common/cd_4558.bin
Downloaded *common/cd_4574.bin
Downloaded *common/cd_5770.bin
Downloaded *common/cd_5774.bin
Downloaded *common/cd_6723.bin
Downloaded *common/cd_6754.bin
Downloaded *common/cd_8453.bin
Downloaded *common/cd_9231.bin
Downloaded *common/cd_12905.bin
Downloaded *common/cd_13181.bin
Downloaded *common/cd_9452.bin
Downloaded *common/ce_1888.bin
Downloaded *common/cf_4532.bin
Downloaded *common/cg_4532.bin
Finished Checking Files
Creating Directory C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\xeBuild\16203\bin
Downloaded *xeBuild/16203/bin/nofcrt.bin
Downloaded *xeBuild/16203/bin/nohdd.bin
Downloaded *xeBuild/16203/bin/nohdmiwait.bin
Downloaded *xeBuild/16203/bin/nomu.bin
Downloaded *xeBuild/16203/bin/notrinmu.bin
Downloaded *xeBuild/16203/bin/patches_falcon.bin
Downloaded *xeBuild/16203/bin/patches_fat.bin
Downloaded *xeBuild/16203/bin/patches_g2corona.bin
Downloaded *xeBuild/16203/bin/patches_g2falcon.bin
Downloaded *xeBuild/16203/bin/patches_g2jasper.bin
Downloaded *xeBuild/16203/bin/patches_g2trinity.bin
Downloaded *xeBuild/16203/bin/patches_g2zephyr.bin
Downloaded *xeBuild/16203/bin/patches_jasper.bin
Downloaded *xeBuild/16203/bin/patches_trinity.bin
Downloaded *xeBuild/16203/bin/patches_xenon.bin
Downloaded *xeBuild/16203/bin/patches_zephyr.bin
Downloaded *xeBuild/16203/su20076000_00000000
Downloaded *xeBuild/16203/xenonclatin.xtt
Downloaded *xeBuild/16203/xenonjklatin.xtt
Downloaded *xeBuild/16203/ximedic.xex
Downloaded *xeBuild/16203/_glitch.ini
Downloaded *xeBuild/16203/_glitch2.ini
Downloaded *xeBuild/16203/_jtag.ini
Downloaded *xeBuild/16203/_retail.ini
Downloaded *common/cba_1927.bin
Downloaded *common/cba_1928.bin
Downloaded *common/cba_4569.bin
Downloaded *common/cba_7378.bin
Downloaded *common/cba_4561.bin
Downloaded *common/cba_4562.bin
Downloaded *common/cbb_1927.bin
Downloaded *common/cbb_1928.bin
Downloaded *common/cbb_7378.bin
Downloaded *common/cbb_4561.bin
Downloaded *common/cbb_4562.bin
Downloaded *common/cbb_4569.bin
Downloaded *common/cd_1927.bin
Downloaded *common/cd_4562.bin
Downloaded *common/cd_4561.bin
Downloaded *common/cd_7378.bin
Downloaded *common/cd_1928.bin
Finished Checking Files
Programming Coolrunner
C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_C_CR_EN_P50.xsvf
Version: 03
Flashing C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_C_CR_EN_P50.xsvf to CoolRunner
Input Filesize: AA78
Output Filesize: 3BBF
Done!
Programming Coolrunner
C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_B_CR_EN_P50.xsvf
Version: 03
Flashing C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_B_CR_EN_P50.xsvf to CoolRunner
Input Filesize: AA78
Output Filesize: 3BAD
Done!
Programming Coolrunner
C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_A_CR_EN_P50.xsvf
Version: 03
Flashing C:\Users\Mike\Documents\J-Runner v02 Beta (287) Core Pack\common\xsvf\RGX_CORONA_A_CR_EN_P50.xsvf to CoolRunner
Input Filesize: AA78
Output Filesize: 3BBF
Done!
Checking Console..
Version: 03
Flash Config: 0x00043000
CB Version: 9188
Trinity
Version: 03
Flash Config: 0x00043000
Writing Nand
nanddump1.bin
Done!
in 2:08 min:sec
Checking Console..
Version: 03
Flash Config: 0x00000000
Can not Continue
Can not continue
Checking Console..
Version: 03
Flash Config: 0x00043000
CB Version: 13181
Corona
Version: 03
Flash Config: 0x00043000
Writing Nand
CORONA_16MB.ecc
Done!
in 0:10 min:sec
Checking Console..
Version: 03
Flash Config: 0x00000000
Can not Continue
Can not continue
Checking Console..
Version: 03
Flash Config: 0x00043000
CB Version: 9188
Trinity
Version: 03
Flash Config: 0x00043000
Writing Nand
nanddump1.bin
Done!
in 2:08 min:sec