Quantcast
Channel: Team Xecuter
Viewing all 6917 articles
Browse latest View live
↧

Question on Patching Tiger woods....

April 11, 2014, 12:33 pm
$
0
0
I like to know how to patch tiger woods 14 for xbox360 for on-line....i got the files i need..but i like to have setting in abgx360_v1.0.5 to burn it....thnx

I dont know if im in the right spot...sorry if im not....
↧
Search

usb comms cord

April 11, 2014, 3:20 pm
$
0
0
usb comms.JPG
got my usb comms cord and I have a couple question :

1. in the pic on pg 26 jrunner pdf it shows two pics one with 3 wires and other with connection as shown is the pic on left (wires only) shows yellow, green & blue wires. and other (like pic above) it show dots on I believe yellow, blue & black labeled? so which is correct?

2. is there any tricks to salvage the adapter? so I can use it with wire only or QSB. or any other way to wire with out destroying cable?

thanks
Attached Images
↧
↧

tut for coroa v6

April 11, 2014, 4:05 pm
$
0
0
hi been trying to hack my corona v6 slim 3 weeks now i have a nandx and a ck3i and a coolrunner v3 lite! i am now looking for a tutorial for this if there is one the xbox slim was given to me on 22/11/13 it was new it has the corona v6 and the drive firmware is 1532 is there such a thing for this late model as i see they are getting harder and harder to hack i will say thanks right here and now for all the great work done by this team were can i get a ltu2 they are like hens teeth cheers again arch:facepalm:
↧

Phat XBOX360 Benq Drive Working in Corona v2 Motherboard

April 11, 2014, 10:21 pm
$
0
0
Here are some images of my Phat XBOX360 DVD Drive Benq Working
On my slim corona v2 Motherboard.
very cool, if you Dont have a DG164S on hand this will work,
remember to always keedp the Nofcrt patch enable.
have fun. :crazy:



↧

RGH Jr Programmer v2 Not Found

April 12, 2014, 1:20 am
$
0
0
I recently purchased the cool runner rev c and jr programmer v2 for my phat falcon, including the nandx qsbs.

The issue I am having is with the jr programmer.

Initially I plugged the jr programmer into my laptop and the hardware manager appeared to confirm it was installing the drivers for the jr programmer. This finished successfully, unfortunately I did not check device manager at this point to confirm it was under processors. At this point the light was a solid green.

I soldered the two qsbs for reading the nandx to my xbox motherboard and then plugged the cables from the qsbs into the jr programmer, then I plugged in the xbox power and did not switch the console on, I then plugged the usb from the jr programmer to my laptop and chose read nand and selected falcon. The output screen in jrunner simply said manually selected falcon and nothing further happened. I touched up the soldering and followed the same procedure a few times (I am running as administrator).

After a few failed attempts I did some digging and I am unable to see the jr programmer in device manager under processors. In fact I am unable to see it under any section, no devices appear with exclamations or question marks. The usb does not make a sound when it is plugged in and when plugging the device in when looking at the device manager screen, the screen does not refresh as you would expect when introducing new hardware. Effectively it is not being seen at all.

I have since plugged it into two further pcs and the driver has not been installed this time, unlike when I first plugged it in and it was acknowledged.

Throughout the jr programmer light has always been green solid. The switch on the side with the reset button is pushed away from the rest button and similarly the switch on the other side of the board (I am not sure what this is), is pushed away from the usb.

I read about potentially resetting the device and updating the firmware in jrunner, I understand the file necessary is PICFLASH_E_1_0_5-JRP-V2.HEX and I have located this. I flicked the switch towards the reset button and then pressed the reset and the light went red. I flicked the switch back away from the reset, plugged the jr programmer into the laptop and attempted to update the firmware, however the message simply says device not found.

I can't seem to find any other information that pushes me any further forward hence the question so if anyone can point me in the right direction or give me some more ideas of what to try I would greatly appreciate it.
↧
↧

Need some help with Coolrunner CR3 Lite install in to a Falcon

April 12, 2014, 2:12 am
$
0
0
hi all im new here, im in need of some help.

i got 2 of the coolrunner CR3 lite in the post today and im trying to find out where a full tut on how to install it in to a falcon xbox360, i have seen alot for the other coolrunners but not for the CR3 lite. can anyone help me out with a wireing diargrame or a full tut?

Thanks :)
↧

New to the forum

April 12, 2014, 2:33 am
$
0
0
Hi everyone.. I'm totally new to xbox community, I bought xbox 360 slim recently and started to know about it, facing some problems regarding installing games on hdd, nevertheless, I'm learning about it and by the help of this forum and you friends I'll reach my goals.
↧

RGH Trinity slim proto v2 is glitching but refuses to boot

April 12, 2014, 3:05 am
$
0
0
I RGH'ed my trinity with the proto v2 and had it booting in 1 to 3 sycles (sometimes 5 or more) with DIP 2, 4, 5, with CAP 10, I think yellow wire on 70 and blue on 47 and it worked for a few months, then it refused to boot even though it was still glitching so I turned off DIP 2 and it went back to normal, another few months later(today) it is again refusing to boot even though it is still glitching, help please!

IMG_20140312_102350.jpgIMG_20140312_102417.jpgIMG_20140312_102625.jpg
Attached Images
↧
Search

Best Hard Drive with links to buy

April 12, 2014, 6:25 am
$
0
0
I'm trying to make sure that I have all the items for a RGH modded xbox 360, well I want to ask is what is the best hard drive choices, as well as links to buy them, excuse my ignorance on the subject- but anything from 500 gb to 1tb will suffice, thank you in advance
↧
↧

RGH Corona 4GB V2 xbox slim lost nand and key

April 12, 2014, 6:29 am
$
0
0
i got corona 4 GB xbox slim V2 from my friend. when it power on green light shows then after some seconds it turn to red. he tried to rgh it. but now nand and key he lost. now i try to make it rebuild . As martin's notes,
i got other corona 4GB nand and i extracted the files.
Renamed the files as KV.bin, SMC.bin, fcrt.bin and smc_config.bin and put these files to xebuild- data folder.
copied the cpukey to the place in j runner.
selected the update 15574 and retail .
create nand without nanddump, typed 2 as LDV and created nand .
wrote the nand in xbox slim using 4gd kit
created ecc
wrote Ecc
Connected DGX . but xell not loading. the green light is showing on the xbox power also the red light in DGX is glowing. the green light is glitching on DGX. but no xell

can you help?
↧

Trinity rev-c RGH help

April 12, 2014, 7:15 am
$
0
0
So I've been working on my trinity for the last few weeks. It's my first one so it's been taking me some time. I've been getting stuck here and there but overall it's gone okay.
2 days ago I dumped the NAND using a JRP v1.1. It gave me 258 and 218 error on every block it read in jrunner, so I checked all my solder points, went over them all and then cleaned them up after. It gave me a perfect read no bad blocks. I copied nanddump_1.bin and saved it as Orig_NAND.bin to my desktop. Then I programmed my coolrunner rev c. When it was done the green light turned off like it was supposed to. I selected trinity, dash 16547 and rgh 2. Then I created ecc. Then I writed ecc. Then the guide I was following said to put the coolrunner in and take the JRP off the board. So I did that. This is my problem, when I was all done. I plugged in the power brick of my box. Put in my av cables. Tryed to turn it on with a controller but it didn't work. So I plugged in the ribbon cable for the faceplate. It beeps but won't turn the box on. The power brick light stays yellow all the time. So I went back and tried to tidy up the board more and go over my soldering. Still no luck. Someone help me please.
↧

I get this on this site

April 12, 2014, 12:16 pm
$
0
0
when i try and upload an image i get this error
Warning: is_writable(): open_basedir restriction in effect. File(/home/mtuktx/public_html/forums/customavatars) is not within the allowed path(s): (/home/teamxecu:/usr/lib/php:/usr/local/lib/php:/tmp) in ..../includes/class_dm_userpic.php o
↧

FIXED corona v2 nand dump good or bad

April 12, 2014, 1:13 pm
$
0
0
hope someone could clear this up for me im dumping the corona v2 nand with the 4gb rw qsb i soldered it to the board got a dump all checked out move them to a file for safe keeping so write the ecc file over to xbox installed proto v2 but console wouldnt boot so reverted back to stock and desoldered the 4gb qsb console wouldnt boot but had a closer look at the motherboard found a short where i cut a wire down removed that console boots fine in stock so i soldered the qsb back on the 360 and took another dump of the nand all 4 nands are the same but if i compare them with 1 of the other ones i have they dont match could it be becouse i moved them they have become corrupted or something wouldnt jrunner tell me that the qsb isnt working properly ive never done a slim corona befor so bit losed in to see if the nand is ok to use on phats it always says about bad blacks and after doing some reading i found out about the Phison chip thank you martin so really all i wanted to know is it ok to use Log.txt
Attached Files
↧
↧

Freestyle Dash , on same HDD as games......possible ?

April 12, 2014, 4:53 pm
$
0
0
hi members , i wondering we you are creating the image to be written to the NAND with JRunner software if you can have Freestyle Dash on the same USB Hard Drive as the games ?


ive seen on Youtube people with a USB stick but i prefer to use a USB Hard Drive...............i want to boot straight into Freestyle Dash below is a pic from the JRunner manual



chat soon


dl.jpg
Attached Images
↧

ANSWERED How to play JPN region game on PAL RGH Console ?

April 12, 2014, 6:30 pm
$
0
0
hi again , i am researching for a future attempt at RGH ......................


i cant get a proper answer through google searches but i have come up with yes you can play JPN games on a PAL RGH Console


thing is i dont know how its done , anyone want to enlighten me ?



chat soon
↧
Search

HI

April 13, 2014, 2:13 am
$
0
0
Hi everyone,

Didn't realize I registered back in 2011 and never made a post. But here is my first one:)
↧

RGH RGH2 Coolrunner need confirmation of the process

April 13, 2014, 3:25 am
$
0
0
I'll try to keep this short.

I have purchased:
jr programmer v2
nandx phat qsbs
coolrunner rev c

I have a phat falcon and currently I have the Qsbs soldered to the board and have successfully taken 4 nand dumps that are confirmed as the same.

The issue is that I have several guides with conflicting information between youtube and tutorials. When duming the nand I am told by this guide:

http://www.ixtreme.net/jtag-rgh/2007...oolrunner.html

Check the number in the 2BL [CB] field. The CB needs to be one of the following to use RGH1.

Zephyr: 4578, 4579
Falcon and Opus: 5771
Jasper: 6750, 6751

Mine reads 5774 therefore I am advised to use the RGH2 method. I am correct in thinking that I do not need to write xell? When writing xell the console boots but the screen is blank both with the hdmi and av cable, I have written back the original nand dump and the console is now displaying again.

Also in accordance with the previous guide after doing the nand dumps, the next thing I needed to do is to program the cool runner using a rgh2 setting in jrunner and selecting falcon for my particular case, I have done this ensuring the cool runner was set to phat and had the prog switch set.

So am I also now right in thinking i simply set the switch to norm and soldering the cool runner to the board in accordance with this guide:

http://team-xecuter.com/forums/showthread.php?t=86539

Using of course the rgh2 wiring method.

Just to sum it up, do I not need xell as many guides and tutorials seems to talk about this and the cpu key etc. Do I simply, dump the nands (done), program the cool runner (done), solder the coolrunner to rgh2 wiring specs and the job done?
↧
↧

RGH Xell Blank screen/black screen Flashing Green Light

April 13, 2014, 7:44 am
$
0
0
Ok second post today.

I have a phat falcon that I am trying to RGH2 using a coolrunner rev c.

I have purchased the qsbs nandx v3 and soldered these to the motherboard. Using a jr programmer v2 I have successfully compared 4 nands and they are the same.

Test 1. I plug the xbox in it boots and the dashboard appears as expected (qsbs attached to motherboard).

Using jrunner I can see:
2BL[CB_A]: 5774 which apparently means I need to RGH2
6BL[CF] Patch 0: 16537

I load nanddump01 as the source, select 16537 as the dash, select RGH2 and click create ecc, then write ecc. The write is successful with 0 errors.

Test 2. I turn on the xbox and the green light on the front flashes continuously, the screen is blank and the TV reports no signal. (qsbs attached to motherboard)

I install the cool runner, remove the resistor from jp and leave the connections unbridged. I remove the resistor for points 1 and 2 and then bridge them. I have not yet tested bridging the cap points. The cool runner is programmed via jrunner under falcon settings.

I wire the coolrunner in accordance with the RGH2 instructions here:
http://team-xecuter.com/forums/showthread.php?t=86539

Test 3. I turn on the xbox and again the light flashes green and a blank/black screen shows, with no signal being reported. (qsbs and coolrunner attached to motherboard)

With the coolrunner installed I flash the nand back to stock, read the nand and then compare against offsite backups to confirm they match.

Test 4. I turn the xbox on and three red light indicating a general hardware failure has occurred.(qsbs and coolrunner attached to motherboard)

I have left the console on for approximately 10 minutes in test 3 stage in order to see if this was due to some form of boot time issue as explained in other threads, however the behaviour remains the same, flashing green light and blank screen.

Firstly does the cool runner need to be installed in order to boot xell? or do you simply flash the nand and you should be able to boot xell regardless of whether the coolrunner has been installed yet.

Second, can anyone suggest why xell would not be booting, if the above is true that coolrunner is not required to boot xell, then surely if I can read/flash the nand successfully I should not need to do much more than simply write xell to the nand and boot the console.

I suppose the last thing is whether there is an alternate method to retrieve the cpu key.

Many thanks
↧

ANSWERED WAP...on the Slim - Trinity

April 13, 2014, 8:27 am
$
0
0
Hey guys:

I took my xbox apart along time ago and I am putting it back together now. I can't remember where the wireless access point gets installed. It sucks getting old!!! Anyway, a quick reminder would help me out a bunch.

Thanks
↧

GENERAL J2C1.1 way to the SB ?

April 13, 2014, 10:42 am
$
0
0
Hi there just got an xbox that has defect from factory J2c1.1 has no 3v , after track this pad i found that he is going to south bridge , any idea ?
↧
Viewing all 6917 articles
Browse latest View live
Search