TX Product(s) used: Slim Proto v2, Slim Post QSB v3, Postfix Adapter v2, Corona 4gb Nand R/W kit
Console Type: Corona v6 - Samsung chip
NAND size: 4GB
Dashboard version: 16756
CB version:
Screenshot of NAND details from J-Runner:JR_screen.jpg
J-Runner log:
domenica 6 luglio 2014 19:26:10
J-Runner v0.3 Beta (4) Started
Checking Files
Finished Checking Files
Corona 4GB Manually Selected
H:\
Reading from H:\ to C:\Users\Manuel\Desktop\XBOX360\output\nanddump1.b in
Done!
in 0:03 min:sec
Initializing nanddump1.bin..
Corona 4GB
RGH2 Selected
Nand Initialization Finished
H:\
Reading from H:\ to C:\Users\Manuel\Desktop\XBOX360\output\nanddump2.b in
Done!
in 0:04 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Writing to H:\ from C:\Users\Manuel\Desktop\XBOX360\output\image_00000 000.ecc
Done!
in 0:00:386 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Images of close-up soldering to motherboard:Crop_on_bridge_and_soldered_points.jpgPostFix_Adapter_v2_crop.jpgSlim_Post_QSBv3_crop.jpgSlimProto_NandReader_crop.jpg
Description of problem: Red Led ok, but no green led on slim proto.
I red that means problems with the post out or the cpu reset, so I did the test of continuity between the pad D of the proto and the point FT3T10, the multimeter beeped so this is ok!
So I thought my problem is the post out. How can i check if the postfix adapter is installed correctly? so if the "spring pin" is touching the right pad under the cgpu?
I have already tried to write the ECC and connect the hdmi cable to the tv, no screen, so i think its not a problem of nand reading/writing.
The first installation i did with 10 cm Yellow cable to postout and 10 cm blu cable to cpu rst 29, then i changed in 12 cm blu cable to postout and the shielded White cable to cpu rst.
I only tried DIP 3-8 cause (if I understood well) I will proced with tuning only when the debug led is working, right?
Last (strange) thing is that if I touch a pad on the postfix adapter with a "pencil" of the multimeter the green led starts working,but not as it should work, only sometimes when i put the top of that pencil on the pad, I noticed that while i was measuring continuity with MM.
Hope someone can help me, I think i miss only a small step to get the cpukey, and sorry for my english.
Thank u very much!
Was the console working before you started: Yes and it works with original nand
Do you get a green debug light appear on the RGH chip every 4-5 seconds: No
How long is the light on for each time: No green light blinking
Edit after 20 min
Reading more threads I found this http://team-xecuter.com/forums/showt...apter+problems, I measured the resistance between Post01 and GND and it is around 0 ohm , not good :(
Is there a way to fix? Thank you.
Console Type: Corona v6 - Samsung chip
NAND size: 4GB
Dashboard version: 16756
CB version:
Screenshot of NAND details from J-Runner:JR_screen.jpg
J-Runner log:
domenica 6 luglio 2014 19:26:10
J-Runner v0.3 Beta (4) Started
Checking Files
Finished Checking Files
Corona 4GB Manually Selected
H:\
Reading from H:\ to C:\Users\Manuel\Desktop\XBOX360\output\nanddump1.b in
Done!
in 0:03 min:sec
Initializing nanddump1.bin..
Corona 4GB
RGH2 Selected
Nand Initialization Finished
H:\
Reading from H:\ to C:\Users\Manuel\Desktop\XBOX360\output\nanddump2.b in
Done!
in 0:04 min:sec
Comparing...
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Can't check for bad blocks. No Spare data. Possibly Corona 4GB
Nands are the same
ECC created
Writing to H:\ from C:\Users\Manuel\Desktop\XBOX360\output\image_00000 000.ecc
Done!
in 0:00:386 min:sec:ms
Initializing nanddump1.bin..
Corona 4GB
Nand Initialization Finished
Images of close-up soldering to motherboard:Crop_on_bridge_and_soldered_points.jpgPostFix_Adapter_v2_crop.jpgSlim_Post_QSBv3_crop.jpgSlimProto_NandReader_crop.jpg
Description of problem: Red Led ok, but no green led on slim proto.
I red that means problems with the post out or the cpu reset, so I did the test of continuity between the pad D of the proto and the point FT3T10, the multimeter beeped so this is ok!
So I thought my problem is the post out. How can i check if the postfix adapter is installed correctly? so if the "spring pin" is touching the right pad under the cgpu?
I have already tried to write the ECC and connect the hdmi cable to the tv, no screen, so i think its not a problem of nand reading/writing.
The first installation i did with 10 cm Yellow cable to postout and 10 cm blu cable to cpu rst 29, then i changed in 12 cm blu cable to postout and the shielded White cable to cpu rst.
I only tried DIP 3-8 cause (if I understood well) I will proced with tuning only when the debug led is working, right?
Last (strange) thing is that if I touch a pad on the postfix adapter with a "pencil" of the multimeter the green led starts working,but not as it should work, only sometimes when i put the top of that pencil on the pad, I noticed that while i was measuring continuity with MM.
Hope someone can help me, I think i miss only a small step to get the cpukey, and sorry for my english.
Thank u very much!
Was the console working before you started: Yes and it works with original nand
Do you get a green debug light appear on the RGH chip every 4-5 seconds: No
How long is the light on for each time: No green light blinking
Edit after 20 min
Reading more threads I found this http://team-xecuter.com/forums/showt...apter+problems, I measured the resistance between Post01 and GND and it is around 0 ohm , not good :(
Is there a way to fix? Thank you.