Console Type: Corona v5
NAND size: 16
Dashboard version: 2.0.16756
Screenshot of NAND details from J-Runner:
http://1drv.ms/1rBPT4X
http://1drv.ms/1rBPU94
J-Runner log:
Images of close-up soldering to motherboard:
http://1drv.ms/1pkMZQi
http://1drv.ms/VPnEkK
http://1drv.ms/VPnF8d
http://1drv.ms/1pkNeea
http://1drv.ms/VPnUA9
http://1drv.ms/VPnV7j
http://1drv.ms/VPnYQD
http://1drv.ms/1q7DeUP
http://1drv.ms/1q7Dm6M
Description of problem:
No green Light on Proto. Xell not booting.
Was the console working before you started: Yes
Details:
I can read and write nand without problems. First I have read the nand, created and wrote ECC. No Green light. After trying a lot with dip switch and pads on QSB I have wrote original nand again. The console booted up without any issues. Once again I read the nand, created and wrote ECC. Once again, no green light on Proto. I have checked all points at least twice already. Please don't mind yellow cable fron QSB underneath the board. I have checked if POST_OUT should be there but nothing changed.
The first log is from reading previous nand with ECC wrote. The second is after loading up original one, creating and writing ECC again (There was original nand already in console but I don't have a log from writing it).
Please help.
NAND size: 16
Dashboard version: 2.0.16756
Screenshot of NAND details from J-Runner:
http://1drv.ms/1rBPT4X
http://1drv.ms/1rBPU94
J-Runner log:
Code:
28 sierpnia 2014 10:21:48
J-Runner v0.3 Beta (4) Started
Checking Files
Finished Checking Files
Version: 10
Flash Config: 0x00043000
00043000
Corona
CB Version: 9188
Trinity
Reading Nand to F:\RGH\J-Runner v02 (278) Core Pack\output\nanddump1.bin
Reading Nand
Error: 250 reading block 141
Done!
in 3:23 min:sec
Reading Nand to F:\RGH\J-Runner v02 (278) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Header is wrong..
Trinity
RGH2 Selected
Nand Initialization Finished
Reading Nand
Error: 250 reading block 141
Done!
in 3:24 min:sec
Comparing...
Bad Block ID 0141 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0141 [Offset: 0x52C200]
Bad Blocks Remapped
Bad Block ID 0141 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0141 [Offset: 0x52C200]
Bad Blocks Remapped
Nands are the sameCode:
===================================================
28 sierpnia 2014 10:29:24
J-Runner v0.3 Beta (4) Started
Checking Files
Finished Checking Files
Initializing nanddump1.bin..
Corona
RGH2 Selected
Nand Initialization Finished
Version: 10
Flash Config: 0x00043000
Writing Nand
nanddump1.bin
Done!
in 3:46 min:sec
ECC created
Version: 10
Flash Config: 0x00043000
Writing Nand
image_00000000.ecc
Done!
in 0:19 min:sec
Tip: Load the nand on source to have quicker results.
Scanning.....
No Xbox Detected
Finishedhttp://1drv.ms/1pkMZQi
http://1drv.ms/VPnEkK
http://1drv.ms/VPnF8d
http://1drv.ms/1pkNeea
http://1drv.ms/VPnUA9
http://1drv.ms/VPnV7j
http://1drv.ms/VPnYQD
http://1drv.ms/1q7DeUP
http://1drv.ms/1q7Dm6M
Description of problem:
No green Light on Proto. Xell not booting.
Was the console working before you started: Yes
Details:
I can read and write nand without problems. First I have read the nand, created and wrote ECC. No Green light. After trying a lot with dip switch and pads on QSB I have wrote original nand again. The console booted up without any issues. Once again I read the nand, created and wrote ECC. Once again, no green light on Proto. I have checked all points at least twice already. Please don't mind yellow cable fron QSB underneath the board. I have checked if POST_OUT should be there but nothing changed.
The first log is from reading previous nand with ECC wrote. The second is after loading up original one, creating and writing ECC again (There was original nand already in console but I don't have a log from writing it).
Please help.