RGH RGH2 Jasper (Pain in my ass)

March 8, 2015, 1:16 am

≫ Next: RGH RGH2 Jasper (Pain in my ass)

≪ Previous: Corona V4 Homemade Nand Reader

$

0

0

got this jasper (16mb) hooked up the ole nand-x and cr rev c got everything working fine read nand and wrote the ecc, console booted xell within seconds. Got my cpu key, wrote xell then i started to write the nand and in middle of writing something went wrong got two bad blocks and console wouldnt boot. shorted the nand chip and re wrote og read console booted up but on retail nand it gives me a 0110 error(3 red rings). this is where im stuck
TX Product(s) used: cool runner rev c, nand-x
Console Type: Jasper
NAND size: 16mb
Dashboard version: 17150
CB version: 6754
Screenshot of NAND details from J-Runner:
(attach an image to your post)
J-Runner log:
updflash.bin log (if applicable):
Image of Coolrunner:
Images of close-up soldering to motherboard:
(attach images to your post)

Description of problem:red ring 0110 after reflashing stock nand(after a bad flash recover)

Was the console working before you started: Y

Do you get a green debug light appear on the RGH chip every 4-5 seconds: Y

How long is the light on for each time:depends on timing file

---

RGH RGH2 Jasper (Pain in my ass)

March 8, 2015, 1:44 am

≫ Next: TUTORIAL: R-JTAG+ ROL NOT WORKING - AUD_CLAMP

≪ Previous: RGH RGH2 Jasper (Pain in my ass)

$

0

0

everything went fine when i wrote the ecc it booted almost instant to xell and i got my cpu key but when i wrote my hacked image it dint glitch within 5-10 mins, flashed back og nand had two bad blocks had to short nand and re write console booted up but got 3 red rings 0110 now im stuck

TUTORIAL: R-JTAG+ ROL NOT WORKING - AUD_CLAMP

March 8, 2015, 3:39 am

≫ Next: Need help with correct stuff for Xbox 360E 250gb/corona v5 CR4

≪ Previous: RGH RGH2 Jasper (Pain in my ass)

$

0

0

If your ROL (ring of light) malfunctions when using the R-JTAG+ method on Phats then I might be able to help you. Just follow a few simple steps:cool2:

INFO

---

This tutorial works for the JTAG_ALT_V1,I am not sure if it works for the v2.

You should just set up the QSB as the original guide except for the switch.
I hope this helped!

Thanks to

briggs01
Krafter

bruno_rv
nofeloniesyet
h1n1viruz

Attached Images

 

Need help with correct stuff for Xbox 360E 250gb/corona v5 CR4

March 8, 2015, 5:06 am

≫ Next: Corona V1 - C5R11 Alt. Point

≪ Previous: TUTORIAL: R-JTAG+ ROL NOT WORKING - AUD_CLAMP

$

0

0

Hi, so I'm going to rgh my 360E/corona v5 and need help making sure I get all the correct stuff.

First, I have rghed my trinity slim so I have the JR programmer v2.

I'm Australian so I'll be buying from ozmodchips, so I'll be getting:

CR4 XL by Team Executer (would this come with the wires?)

Xecuter CR4 XL Slim QSB v3 Kit

Xecuter Corona PostFix Adaptor v2

Is that all I need or am I missing something? thanks in advance :-)

Also, for those that have used the new CR4 XL on a corona v5, what's your experience, is it always instant boot? :-)

Corona V1 - C5R11 Alt. Point

March 9, 2015, 2:29 am

≫ Next: R-JTAG JTAG Alt Kit

≪ Previous: Need help with correct stuff for Xbox 360E 250gb/corona v5 CR4

$

0

0

Hey folks,

Just a quick question what is the best alternate point for the cpu_rst (C5R11)
I don't want to remove the x-clamp because i don't have the tools for it yet.
I have read that there are some points but some people where talking about bad boot times and stuff or is that bs?

Thanks for the reply's already ;) :cool2:

R-JTAG JTAG Alt Kit

March 9, 2015, 2:58 am

≫ Next: dead trinity ..

≪ Previous: Corona V1 - C5R11 Alt. Point

$

0

0

Does anyone know where I could get the Xecuter Non-Xenon JTAG Alt Kit in the UK or Europe? It was missing from a R-Jtag kit I bought

dead trinity ..

March 9, 2015, 8:05 am

≫ Next: HITACHI NON-79 Bricked Hitachi GDR-3120L will not open or react to open button.

≪ Previous: R-JTAG JTAG Alt Kit

$

0

0

Hi there,

i become one Xbox 360 trinity DEAD,

i erased the nand completly, 16MB flashed an ECC generated by AutoGG, no the console starts spinning crazy, and lighting Green light rapidly.

After ECC write i placed x360run, to get in to Xell, no luck...

So, flashing with jrunner...

Checking Files
Checking Console..
Version: 01
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9188
Trinity
Connection Error
Glitch2 Selected
CR4 Selected
Version: 01
Flash Config: 0x00023010
Writing Nand
TRINITY_CR4.ecc
Failed to write 0x0 block
Failed to write 0x1 block
Failed to write 0x2 block
Failed to write 0x3 block
Failed to write 0x4 block
Failed to write 0x5 block
Failed to write 0x6 block
Failed to write 0x7 block
Failed to write 0x8 block
Failed to write 0x9 block
Failed to write 0xA block
Failed to write 0xB block
Failed to write 0xC block
Failed to write 0xD block
Failed to write 0xE block
Failed to write 0xF block
Failed to write 0x10 block
Failed to write 0x11 block
Failed to write 0x12 block
Failed to write 0x13 block
Failed to write 0x14 block
Failed to write 0x15 block
Failed to write 0x16 block
Failed to write 0x17 block
Failed to write 0x18 block
Failed to write 0x19 block
Failed to write 0x1A block
Failed to write 0x1B block
Failed to write 0x1C block
Failed to write 0x1D block
Failed to write 0x1E block
Failed to write 0x1F block
Failed to write 0x20 block
Failed to write 0x21 block
Failed to write 0x22 block
Failed to write 0x23 block
Failed to write 0x24 block
Failed to write 0x25 block
Failed to write 0x26 block
Failed to write 0x27 block
Failed to write 0x28 block
Failed to write 0x29 block
Failed to write 0x2A block
Failed to write 0x2B block
Failed to write 0x2C block
Failed to write 0x2D block
Failed to write 0x2E block
Failed to write 0x2F block
Failed to write 0x30 block
Failed to write 0x31 block
Failed to write 0x32 block
Failed to write 0x33 block
Failed to write 0x34 block
Failed to write 0x35 block
Failed to write 0x36 block
Failed to write 0x37 block
Failed to write 0x38 block
Failed to write 0x39 block
Failed to write 0x3A block
Failed to write 0x3B block
Failed to write 0x3C block
Failed to write 0x3D block
Failed to write 0x3E block
Failed to write 0x3F block
Failed to write 0x40 block
Failed to write 0x41 block
Failed to write 0x42 block
Failed to write 0x43 block
Failed to write 0x44 block
Failed to write 0x45 block
Failed to write 0x46 block
Failed to write 0x47 block
Failed to write 0x48 block
Failed to write 0x49 block
Failed to write 0x4A block
Failed to write 0x4B block
Failed to write 0x4C block
Failed to write 0x4D block
Failed to write 0x4E block
Failed to write 0x4F block
Done!
in 0:32 min:sec

Flashing with AutoGG
, with AutoGG and swapping the ecc file auto generated in autogg, TRINITY_CR4.ecc from jrunner i flashed the ECC, with no errors.

HITACHI NON-79 Bricked Hitachi GDR-3120L will not open or react to open button.

March 9, 2015, 12:40 pm

≫ Next: R-JTAG Successful Repair/R-Jtag on Falcon + Possible fix for high fan speed/Fatal Crash Int

≪ Previous: dead trinity ..

$

0

0

As sated in title have 2 bricked Hitachi one is 58 other 78 it seems that JF hang and end up with 2 bricks any way to recover with external programmer .

---

R-JTAG Successful Repair/R-Jtag on Falcon + Possible fix for high fan speed/Fatal Crash Int

March 9, 2015, 1:18 pm

≫ Next: [Trinity] Not booting retail neither glitch on CR4

≪ Previous: HITACHI NON-79 Bricked Hitachi GDR-3120L will not open or react to open button.

$

0

0

Picked up a few broken phat Xb360's from the flea market 2 weeks ago, I saw some nand wires while inspecting one of them and opened it up when I got home. It had a Rjtag V1.0 and all required QSBs on Db 16203, noticed they hacked R4B24 to bits (I assume they had a Coolrunner in it at some point).The resistor was long gone and replaced by a very poor trace repair smothered in hot glue, which consisted of large globs of solder. No water damage or any other deep fried points.

Console booted( fan speed on boot seems too fast), 20+ cycle before Xell appeared-- Got CPU Key
Dumped Nand - 3 bad blocks
Got KV
Built New DB - No bad blocks

Changed the settings to:
DIPs - 3 - 7 ON
470 - Middle switch
Aud_clamp

Console Instant Boots (Fan speed issue remains)
Start playing Skyrim from HDD
5 minutes in the console fan is running at 100% and ERAM is way too hot for normal gameplay....Fatal Crash Intercepted kept repeating. Game Froze.
Shut down to cool
Tried again with GTA V. Fatal Crash Intercepted again

Did some research and saw this seems to be common problem with hardly any answers beside messing with SMC_config or applying new thermal compound. GPU isn't the problem in my case, wasn't out of operating temps.

Edited the SMC-Config to all the recommended setting - No Difference

Turned my attention to the piss poor trace repair, not quite reading 33 ohms.

Flipped the board over, soldered a wire to C4N27 and then to the far end of the broken trace on R4B24 and it worked perfectly.
Fan has stabilized, No more Fatal Crash Intercepted, and I get WTF! on the pro rater.
Playing GTA V all day without a hitch.

Maybe this will save ppl some unnecessary work on the GPU, Check your temps 1st before pulling off the heatsink thinking you need to replace thermal compound.

[Trinity] Not booting retail neither glitch on CR4

March 9, 2015, 1:22 pm

≫ Next: J4C1(Standby Header, Xbox): Where do I go from here?

≪ Previous: R-JTAG Successful Repair/R-Jtag on Falcon + Possible fix for high fan speed/Fatal Crash Int

$

0

0

Hi,

I have a problem with a Trinity console that I tried to glitch with CR4. Could you please help me with some hints?
Initially I installed with Demon, reading Nand and trying to glitch it, without success. Now the console is not booting retail. I removed the Demon and also CR4 and I re-soldered all the pins for CR4 and using J-R Programmer V2 instead on Demon. I loaded the saved Nand and written back as retail but console is not booting.. ROL on red after 5 seconds. I tried to glitch it once again, without success.
Logs looking like this:

Initializing nanddump1.bin..
Trinity
Glitch2 Selected
Nand Initialization Finished
Retail Selected
Version: 10
Flash Config: 0x00023010
Writing Nand
nanddump1.bin
Done!
in 3:36 min:sec

Checking Files
Finished Checking Files
Checking Console..
Version: 10
Flash Config: 0x00023010
00023010
Trinity, Jasper 16MB
CB Version: 9231
Trinity
Glitch2 Selected
CR4 Selected
Version: 10
Flash Config: 0x00023010
Writing Nand
TRINITY_CR4.ecc
Done!
in 0:18 min:sec


Version: 10
Press Escape to exit
Waiting for POST to change
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 0E
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 0A
Post 0B
Post 0C
Post 0D
Post 0E
Post 03
Post 04
Post 05
Post 06
Post 07
Post 08
Post 09
Post 0A
Post 0B
Post 0C
Post 0D
Post 0E




anc continuing cycling :(.

Thanks in advance!

J4C1(Standby Header, Xbox): Where do I go from here?

March 9, 2015, 1:28 pm

≫ Next: DRIVERS JR-Programmer v2 - Glitch

≪ Previous: [Trinity] Not booting retail neither glitch on CR4

$

0

0

Hello everyone.

My friend recently handed his Xbox Slim over to me because it wasn't powering on, yet it was making the dinging noise when you pressed either the eject or power button. Before I start going into detail, I just want to say I am no longer troubleshooting with the basics. Yes, I have tried a different power supply and tried powering the console on with a controller.

Anyways, I was probing the standby headers of the console with a multimeter and everything checked out except for one of them, which in this case was J4C1. Its voltage reading was 0.01, which is very low. I have read that it may be a MOSFET that is blown, but I just need some clearance before I try anything.

Thanks for all of the help!


Also, the console is a 2013 4GB Slim if anyone was wondering.

DRIVERS JR-Programmer v2 - Glitch

March 9, 2015, 4:20 pm

≫ Next: JTAG noobs 1st go at jtag couldnt "add dashlaunch patches"

≪ Previous: J4C1(Standby Header, Xbox): Where do I go from here?

$

0

0

Hi Interwebs people!

So.... I have a problem. For about 2 hours I have been playing around with an RRODed Xbox I have sitting around. A couple MB tracers are broken, and it heats up fast. I did an at-home reball/reflow which got rid of the E74 error I was getting first, but now it is getting the RROD. Anyways, what I am trying to do is get Xell written onto the Nand and then run a quick CPU Key grab with my CR4 XL. I have don't a little bit of research and apparently others have done this as well so it should work but...
After soldering the points for my JR-Programmer, I plugged in the JR-Programmer into my USB port it doesn't respond in J-Runner. A couple months I RGHed a Trinity with the same process (The RRODed Xbox is a Falcon BTW) and I had the same problem. To fix it I uninstalled and deleted the old PTL... USB driver and DLL files. Then I re-installed the JR-Programmer drivers in Device Manager with the Microsoft Driver Signature Verification off. I have spent the last hour and a half doing that, over and over again. I am not to the point where I think the actually flash memory of the JR-Programmer is shot... Anyways, if anyone has some knowledge that could help me fix this it would be highly appreciated.

Regards,
A5u5Ra23rH3r0.

JTAG noobs 1st go at jtag couldnt "add dashlaunch patches"

March 10, 2015, 1:51 am

≫ Next: R-JTAG Xecuter Nand-X JTAG KIT #5

≪ Previous: DRIVERS JR-Programmer v2 - Glitch

$

0

0

hi.
i work at a pc/console shop,a electronics tech,
but 1st time trying to jtag.dumped nand
and got cpu key then problems,i have checked forum.
i have updated...should i allway go with the latest dash.17k
thanks jk
10 March 2015 08:36:33

J-Runner v0.3 Beta (7) Started



Checking Files
Finished Checking Files
Downloaded *xeBuild/12625/_jtag.ini
Finished Checking Files
Initializing nanddump1.bin..
Xenon
Jtag Selected
Nand Initialization Finished
Load Files Initiliazation Finished
Clean SMC detected
12625
Couldn't add dashlaunch patches to C:\Users\User\Desktop\xbox\xeBuild\12625\_glitch.i ni
Couldn't add dashlaunch patches to C:\Users\User\Desktop\xbox\xeBuild\12625\_glitch2. ini
Couldn't add dashlaunch patches to C:\Users\User\Desktop\xbox\xeBuild\12625\_glitch2m .ini
Started Creation of the 12625 xebuild image
KV Info saved to file
---------------------------------------------------------------
xeBuild v1.14.693
---------------------------------------------------------------
base path changed to C:\Users\User\Desktop\xbox\xeBuild
---- { Image Build Mode } ----
building jtag image

---------------------------------------------------------------
C:\Users\User\Desktop\xbox\504838764305\updflash.b in image built, info:
---------------------------------------------------------------
Kernel : 2.0.12625.0
Console : Xenon
NAND size : 16MiB
Build : JTAG
Xell : power on console with console eject button
Serial : 504838764305
ConsoleId : 027061590190
MoboSerial: 7768173204176425
Mfg Date : 10/23/2006
CPU Key : 2FEE91CA5582DB0334BEEA845C5A137C
1BL Key : DD88AD0C9ED669E7B56794FB68563EFA
DVD Key : 20F3E3A6A5DDDD87617EA6566153332F
CF LDV : 4
KV type : type1 (no hash)
---------------------------------------------------------------
xeBuild Finished. Have a nice day.
---------------------------------------------------------------
Saved to C:\Users\User\Desktop\xbox\504838764305
Image is Ready
Initializing updflash.bin..
Xenon
Nand Initialization Finished

R-JTAG Xecuter Nand-X JTAG KIT #5

March 10, 2015, 2:58 am

≫ Next: TRINITY [CR4]Trinity CR4 will not glitch

≪ Previous: JTAG noobs 1st go at jtag couldnt "add dashlaunch patches"

$

0

0

Hi,

Im wondering if anyone has one of these for sale, Im based in Ireland

Any help would be great!

TRINITY [CR4]Trinity CR4 will not glitch

March 10, 2015, 4:51 am

≫ Next: FS3 problem...

≪ Previous: R-JTAG Xecuter Nand-X JTAG KIT #5

$

0

0

I have a trinity I was successfully able to glitch last week. Boot times varied in between instant-1 min.

Now today it doesn't want to move a muscle. I am going to show you pictures, ask basic stupid questions to rule stupidity out, and then explain myself how I think I went wrong, and then let you guys decide hopefully.

First thing. Why I think it might not work:

I picked up the ethernet cord going into the console, the otherside shocked me, did I fry anything? Maybe the CR4?

What I did to test: Re-flashed stock nand...success! Console boots and console is banned :( (from last week lol)

So I re-created the Xebuild (didn't bother flashing ecc because I had CPU key) and it won't glitch. I tried flashing just ecc, still no glitch.

Left Xbox on overnight, woke up...still not glitch, just sitting there flashing green every 3 seconds.

My questions:

CPU_RST does not need to be soldered in my situation, right?
In Xebuild, I select Trinity, RGH2, and the CR4 option, right?
Recommended CR4 dip settings, resistance, Ohm jumper?

Thanks for reading and hope for quick assistance.

Pictures:

Notes: white wire goes from underboard CPU_RST to nothing, and the soldering seen below is not my best, just fast work, and blue wire is indeed connected, I assure you, I know it is hard to see, but it is in the right place.




Picture took in the middle of a glitch (green light does not stay on)

Attached Images

        

---

FS3 problem...

March 10, 2015, 5:46 am

≫ Next: xDrive Plus & xFan Sata Exchange unit Issue

≪ Previous: TRINITY [CR4]Trinity CR4 will not glitch

$

0

0

Hi, Just a little problem.
I got FS3 installed boots fine.
Boots games fine.
Once I'm in a game and I hit the big "X" then "Y" to go back to FS3 but it just sits at a black screen.
I have to turn it off and back on again to get back into FS3.
Games are on a HDD.
FS3 & Dash Launch are on the internal memory.
Not entirely sure if that matters.

Thanks for your time,
Kyle.

xDrive Plus & xFan Sata Exchange unit Issue

March 10, 2015, 6:08 am

≫ Next: BENQ slim trinity benq drive question

≪ Previous: FS3 problem...

$

0

0

the sata exchange unit i broke the bottom sata connector being stupid long story anyways can i use the top one to plug into the main on the board if so do i have to hook up anything different? Or is there a way to buy another one. Thanks.

BENQ slim trinity benq drive question

March 10, 2015, 9:52 am

≫ Next: Swaping R-JTAG with CR4

≪ Previous: xDrive Plus & xFan Sata Exchange unit Issue

$

0

0

I couldn't update a halo reach system so I opened it and Surprisingly it had a modified benq drive with some sort of chip that connects to the drive board, the console motherboard and the rf module Could some one please tell me what this mod chip is called or what is it for?

Attached Images

    

Swaping R-JTAG with CR4

March 10, 2015, 3:35 pm

≫ Next: Do backups degrade?

≪ Previous: BENQ slim trinity benq drive question

$

0

0

NVm. testing it with multimeter

Do backups degrade?

March 10, 2015, 7:18 pm

≫ Next: [USA] Looking for a cr4 or two

≪ Previous: Swaping R-JTAG with CR4

$

0

0

I think my DVD drive is shot but just to make sure...
Do backups degrade over the course of a few weeks? Back in January, I managed to get my 360 working with my backups, played just fine for all of winter break. Went back to school for a couple weeks and now I'm home on spring break. The console won't read the disc (gives me that "disc could not be read" message that advises cleaning the disc or restarting the console), which is odd since the only thing that happened to the console in the interim was it was put in a cabinet. The disc surface is pristine, no scratches, no fingerprints, nothing, and the dye layer looks to be consistent, with no dark spots or streaks. As far as I can tell, this backup should still play.

I played with the trim pot levels a bit; turning the laser pot out to 3.6 k renders the drive completely unable to even read the disc, it thinks there's nothing in there. Turning the pot down seems to help, but I dropped it down to 2.7 k and it's still not reading (the screen fades to black, stays black for a few seconds and then the error message comes up). This console was plagued with read errors even before I flashed it, I was also having issues with textures popping in and whatnot when the game actually worked (this was an OEM disc that lived in the console, which was never dropped or disturbed while running). THAT disc eventually developed a hairline crack due to manufacturing error, which led to me flashing the console when I was refused a refund, but anyway... Am I right in assuming that I probably need a new laser diode or something else in the drive has gone wrong?